How to Remove the Door on Your Browning Gun Safe: Step-by-Step Guide

Unlock the secrets of easily removing the door on your Browning Gun Safe with our straightforward steps, and never struggle with transporting or storing it.

Browning gun safes store firearms, ammo, and valuables securely. They’ve got **fireproof**, foolproof, and anti-theft features, plus protection from hazards. 

If you own Browning gun safe, learning how to remove the door is necessary. Keep reading the step-by-step process for the safe removal of a Browning gun safe.

Preparations Needed Before Removing Your Gun Safe’s Door

You can’t just remove your gun safe with your hand alone. That’s why here are the essential components you’ll need when removing your gun safe’s door safely and securely.

1. Ask other people to help you.

As mentioned above, you can’t remove your gun safely with bare hands unless you’re some fictional Greek mythology character. However, you can remove it without using other tools that could potentially harm the gun safe than preserve it. Ask for someone to assist you when removing the door of your safe.

2. Wear appropriate protective gear.

When it comes to metal, edges might still be sharp, despite the Browning gun safe being manufactured flawlessly. Wearing boots and gloves is best to avoid slipping or dropping the door on your foot.

3. Check the owner’s manual for specific instructions.

To avoid mishandling your gun safe or any part of it, always use the owner’s manual, which the manufacturer provided as a guide on proper maintenance and usage. Also, the manual will contain the do’s and don’ts regarding gun protection. 

4. Empty the contents of the safe.

Before transporting or removing the door of your safe, you must always remove all the contents of your gun safe. This can avoid instances or the potential hazard of an accidental discharge that could endanger the lives of the people moving it or those in the area.

5. Gather the tools to remove your gun safe.

Although it is highly advised not to do this, use a screwdriver and a hammer to remove the hinge pin on your gun safe door. Only use this way if you have no choice because your gun safe door is stuck.

Steps in Removing Your Browning Gun Safe Door

Gun safes are known to be heavy. Therefore, I have written down the safest way how you can remove your Browning gun safe door.

Step 1: Open the safe door to a 110-degree angle.

Dial the correct combination to your Browning gun safe or insert the key, depending on which model you bought. As doors are made durable and foolproof from the outside, you can only remove the gun safe door by making sure that the door is open first.

Step 2: Lift the door and remove it.

With gun safe sharing fireproof features, its weight will be heavier than the usual safe door. Gun safes are lined with different materials. Hence, you’ll need a companion to accompany you in lifting the door to remove it from the hinge pins keeping it in place.

Step 3: Locate the hinge pins.

Depending on the model type, most hinge pins can be found on the safe frame holding both the door and the vault. Hinge pins are cylindrical, removable, and non-removable metal rods running through hinges and keeping them together.

Step 4: Remove hinge pins.

After you’ve located the hinge pins, use your screwdriver and the hammer to remove them. Always remember that in case you’re not skilled in doing this, it’s best to entrust it with someone who knows about it that’s reliable.

Reattaching Your Browning Gun Safe Door

Now that you’ve finally moved your gun safe to another location, it’s time to reattach it. You can learn to do this by following these steps:

Step 1: Insert the hinge pins.

The pins are the very object that will hold the door to the gun safe in place. Place it inside the hole on the hinge.

Step 2: Position your door at a 110-degree angle.

You must never forget to align your door at a 110-degree angle or the same way you took it out. And then, make sure the holes on your door’s bottom and top hinges align with the pin so it goes in.

Step 3: Test the door.

Before you place your firearms inside your gun safe, you must test and understand its locking mechanisms and whether the door works properly. That way, in case you’ve damaged it, or if a part of it needs repairs by an expert, you can always get it to them without worrying about your firearms.

Maintenance of Your Browning Gun Safe Door

A Browning gun safe is a long-term investment as it is built with top-quality construction and materials that guarantee it will last for a long time.

That’s why if you want to utilize your Browning gun safe door to its fullest potential, please take note of the following:

1. Regularly check the hinges and door.

Check if your hinges and doors are still working correctly. If they aren’t, you can use a lubricant or silicone spray so that it works smoothly.

2. Clean the hinges and door.

Your door and hinges are like a gateway to the condition of your entire safe. That’s why if your doors or hinges aren’t working properly, or if it’s making those cracking noises akin to rust, check the hinge pins.

3. Check the lock’s battery.

Always remember that if a digital gun safe has run out of battery, you cannot open it once you’ve closed it. Always remember that if you have a digital lock or a biometrics one, they both run on battery.


Overall, a Browning gun safe is wholly built to be durable, with fireproof, foolproof, and robust locking mechanisms. However, its shelf life will depend on proper maintenance.

Always remember that the gun safe door also adds to the total weight of the whole gun safe. If you plan on moving it to another area within your home or to another residence, place your guns somewhere safe and its contents to avoid accidents or damages.


Why would I remove the door on my Browning gun safe?

It is to prevent the sudden opening of the door during transit. Other than that, a Browning gun safe also adds significant weight to the total gun safe; thus, removing it will make it a little lighter. 

What tools do I need to remove the door on my Browning gun safe?

To successfully remove your Browning gun safe door, you may or may not need only a few items, such as a screwdriver and safety gloves. Also, you need at least two to three people to lift the door off the hinge together to avoid accidents.

Are there any precautions I should take when removing the door on my Browning gun safe?

Always remember not to experiment, such as tampering with your locking mechanism or any part. Moreover, keep the hinge pins since they will hold both your gun safe door to your whole gun safe.

Will removing the door of my Browning gun safe affect its warranty?

Any unauthorized repairs or tampering done unto your Browning gun safe will nullify its warranty. However, removing the door, as long as you don’t tamper or lose any part of it, will not affect its warranty.


Yizhak, Ilan. “Heavy Safes: Why Weight Is Important for High Security.” INKAS® Safes Manufacturing, Mar. 2023,

“Browning ProSteel Gun Safe Warranty.”,

Gun Safes – Browning ProSteel.

Aspireadmin. “How to Stop or Fix a Squeaky Door and Best Lubricant for Door Hinges.” Aspire Doors, 20 Sept. 2021, 

Leave a Reply

Your email address will not be published. Required fields are marked *